Advanced
Secure Online Ordering With Full 128 Bit Card Encription
Online Catalogue
>
Large Model Units
Powersave (Split Supply)
The Powersave is designed to remove the need for the current drawn by all servo’s from passing through the receiver and is for use with receivers that ARE voltage sensitive. Please note that this unit is not optically isolated.
This unit requires the use of servo batteries only, the RX is powered from the same supply. The servo supply can be either 4.8v direct or 6.0v battery backed (please check that all equipment to be used is able to handle the higher voltage ie 5 cells minus 0.7 v diode drop).
The unit has twelve short fly leads fitted with universal plugs for connection to the receiver and twelve standard pin block connectors for connection to the servo’s. Power for the servo’s is supplied via either the 4,8v direct connection or the two 6,0v battery backer inputs. Battery monitor connections are available for use in backer configuration (use any servo output for 4.8v configuration).
Datasheet
Price £29.95
(Including: VAT at 17.5%)
Quantity:
Powersave (Common supply)
The Powersave is designed to remove the need for the current drawn by all servo’s from passing through the receiver and is for use with receivers that ARE NOT voltage sensitive. Please note that this unit is not optically isolated.
This unit requires the use of servo batteries only, the RX is powered from the same supply. The servo supply can be either 4.8v direct or 6.0v battery backed (please check that all equipment to be used is able to handle the higher voltage ie 5 cells minus 0.7 v diode drop).
The unit has twelve short fly leads fitted with universal plugs for connection to the receiver and twelve standard pin block connectors for connection to the servo’s. Power for the servo’s is supplied via either the 4,8v direct connection or the two 6,0v battery backer inputs. Battery monitor connections are available for use in backer configuration (use any servo output for 4.8v configuration).
Datasheet
Price £29.95
(Including: VAT at 17.5%)
Quantity:
SM96 MPB (Model Power Board)
Size: width 54 mm height 96 mm depth 28 mm weight 160gms.
The Model Control Unit is a complete power and signal system for use in large models (under 20Kg).
It has been designed to electrically disconnect (optically isolate) all servo's and their associated wiring from the receiver, thereby eliminating all interference entering the receiver via the servo connections.
Data Sheet
Price £74.95
(Including: VAT at 17.5%)
SM33 Opto Isolator
Size: width 38 mm height 56 mm depth 20 mm Weight 42gms.
The Opto Isolator Unit is designed to electrically disconnect and isolate all servos and their associated wiring from the receiver, thereby removing all radio frequency interference entering the receiver via the servo connections. The use of this unit has several other benefits including improved receiver operating range and the possibility of running the servos and receiver on different supply voltages. The unit is supplied with eight short fly-leads fitted with universal plugs for connection to the receiver and eight standard pin connectors for connection to the servos.
Data Sheet
Price £29.95
(Including: VAT at 17.5%)
Quantity:
SM34 Backer Monitor
Size: width 38 mm height 20 mm depth 67 mm weight 30gms.
The Backer Monitor is designed to allow two 5 Cell receiver batteries to be connected to one receiver. If either battery fails it will automatically be blocked from affecting the remaining functional battery. Each battery is separately monitored for safe operation and the current state is indicated by red and green LED indicators, the switching point is set at 5.95v + or - 50 mv. This unit will NOT work with standard 4.8v receiver packs. Connections are via screw block connectors.
Data Sheet
Price £13.95
(Including: VAT at 17.5%)
Quantity:
SM95 Screw Jack Controller
Size: width 56 mm height 48 mm depth 21 mm weight xxgms.
The controller is a micro processor operated unit designed to simplify the use of motor driven retract and flap control systems. The signal from the receiver is used to decide where the retract should be. The micro processor then checks to see if the retract is in the required position, if it is not then power of the correct polarity is then supplied to the motor until the limit micro switch operates, power is then removed until the next operating sequence is demanded.
Data Sheet
Price £34.96
(Including: VAT at 17.5%)
Quantity:
SM47 Engine Kill Switch
Size: width 28 mm height 20 mm depth 45 mm weight 20gms.
This module is designed to allow the control of an electonic ignition system using a spare switched transmitter channel. The ignition system is automatically disabled if the receiver is switched off. Connections are via screw block connectors.
Data Sheet
Price £16.96
(Including: VAT at 17.5%)
Quantity:
SM32 Failsafe
Size: width 33 mm height 23 mm depth 15 mm Weight 15gms.
The FailSafe is a micro computer controlled unit designed to detect both the loss of receiver output control signals as well as detecting corrupted signals. The computer will go into fail safe mode after finding 100 missing or corrupted control pulses. Upon receiving 10 valid pulses the computer will return to normal operating mode. The servo fail safe position is adjustable across the complete servo range in 6.25% steps. Connections are via universal plug fly-lead to the receiver and pcb mounted pin connector to the servo.
Data Sheet
Price £17.95
(Including: VAT at 17.5%)
Quantity:
SM75 Futaba Type Heavy Duty Switch
The Heavy Duty Switch Harness has been produced to reduce the potential of over-loading a standard switch harness when used in quarter scale and above models. The switch and the wire have been up-rated to a six amp carrying capacity. The switch type used is a 2-pole toggle type with a locking actuator. Both positive and negative wires are switched giving total battery isolation.
Price £12.95
(Including: VAT at 17.5%)
Quantity:
SM76 JR Type Heavy Duty Switch
The Heavy Duty Switch Harness has been produced to reduce the potential of over-loading a standard switch harness when used in quarter scale and above models. The switch and the wire have been up-rated to a six amp carrying capacity. The switch type used is a 2-pole toggle type with a locking actuator. Both positive and negative wires are switched giving total battery isolation.
Price £12.95
(Including: VAT at 17.5%)
Quantity:
Online Catalogue
>
Large Model Units
Secure Online Ordering With Full 128 Bit Card Encription
